The most important network of trusted contractors in Canada
I need a wood deck floor built for a balcony. It is 8x11. I’d like it built in two sections so that I can lift up and clean underneath from time to time. It will be on a concrete surface and will have outdoor furniture top. I want a quality deck preferably with wood lumber. I would be happy to buy the lumber or to have the contractor buy the lumber as part of the quote. Ideally, the lumber is 11 feet long boards but flexible. It would require the building and assembly of the decking floor.
1. Purchase and install shower glass door (the door to be purchased by the contractor)
2. Tile and grout shower walls 5 ft x 5 ft
3. Install shower faucets and sink faucets (we will purchase faucets)
4. Tile and grout shower floor approx. 5 ft x 5 ft
5. Plaster all areas as needed
6. Prime and paint exposed drywall 5 ft x 5 ft
7. Install vanity with faucets (we will purchase both vanities)
8. Install new toilet (we will purchase)
9. Install new light fixture (we will purchase)
10. Install light switch and receptacle
11. Frame, drywall area beside shower 5 ft x 5 ft
12. Install shelving (we will purchase shelving)
1. Remove and dispose of the existing bathtub
2. Install drywall aqua board in bathtub area approximately 5 ft x 5 ft
3. Demolition of 2 non-load bearing walls (10 ft x 7.5 ft and 12 ft x 7.5 ft) and garbage disposal
4. Finishing of areas where demolition has been done
5. Remove baseboards throughout approx. 21 ft x 30 f
6. Remove laminate floor 10 ft x 11 f
7. Patch up walls as necessary, plaster tape as necessary
8. Painting primer 2 coats and pain 2 coats approx. 31 ft x 47 f
9. Remove and dispose of wooden shelving size 6 ft x 2 ft
10. Laminate floor installation approx. 7 ft x 30 f
Replacement of 3 windows in the basement
Window space needs to be cut and a window well supplied.
I'm looking for an inexpensive linoleum in a kitchen that is about 12' x 10'6" and a connected back entryway about 7' x 3'2". I have pulled up an old layer of the stick on lino tiles and cleaned up the adhesive as best I can using acetone. What's left is the old original lino, and I'd like the new flooring to just go on top of that.
Kitchen renovation with the full gutting of existing kitchen, floor, ceiling and walls. Size approx. 12x15 ft. Insulation of exterior wall. Tile or floating floor. Move some plumbing and electrical. New kitchen cabinets to be installed.
This job is only open to contractors who possess a current City of Toronto license. This is for a house built in 1948 measuring 40' by 22'. An outline of services is as follows:
Part A – General Upgrades:
2) Remove/Replace Dismantled Brick Facing near front stairs of the house – remove/replace where required, to try to match existing facing
3) Repair a routine Water Leak – for the inside tap beside basement window that controls water flow to outdoor hose
4) Paint ceilings only in 5 rooms
Part B - “Accessibility Upgrades” Required at 49 Lunness Road:
1) Install new flooring in kitchen and bathroom, and reinforce structures as may be required
2) Eliminate trip hazards inside the house by leveling raised floorboards in 2 upstairs areas
3) Eliminate potential trip hazard at the side entrance to the house
4) Front Steps – reinforce railing which currently shakes when held; make repairs to concrete steps
We recently purchased a condo and we are looking to replace the carpet in two bedrooms with laminate flooring and replace the linoleum flooring in the laundry room and cork flooring in kitchen and entryway with tiles. The total square footage of the apartment is approximately 1200 square feet, and the areas that require updates make up a little less than half of the apartment.
I own a 45-year-old detached back split home. Currently, the ventilation of the roof is very poor and I have mold underneath the sheathing. I would need to remove all shingles, remove all plywood on the top floor and perimeter plywood on the lower floor (to see if mold present), remove old insulation or add more blown in cellulose.
I would need proper vents instated such as ventilation max brand, connect the washroom and kitchen hood fan to vent outside the roof. I would also need air baffles installed throughout the perimeter of the roof to allow fresh air intake. I would feel more confident an experienced licensed carpenter perform the plywood and roofing materials installation as per code to avoid warping and damage from high-velocity winds. I would also prefer shingles be installed and nailed for high-velocity winds. I need someone that has a proven track record with references and knowledge of building science.
- My bathroom is approx. 6.5' x 6.5'
- Looking to do a full gut (new bath, floor, vanity etc...)
- Not looking to move any plumbing points